RFID News

News and knowledge for the RFID industry

ETSI puts Europe’s UHF RFID standard EN 302 208 to the vote, as railway radio squeezes the fourth upper-band channel

ETSI has sent the next version of Europe’s UHF RFID reader standard out to a vote. Draft EN 302 208 V3.5.0, dated November 2026, went into combined public enquiry and vote on 9 November 2026, and voting closes on 1 February 2027. Nothing moves in the frequencies or the power limits. The only change ETSI’s own change log records is to the test methods. The more revealing edit is in the citations, where the draft explains that the fourth channel of the upper band no longer rests on the same legal footing as the other three.

Some context for anyone arriving cold. ETSI, the European Telecommunications Standards Institute, writes the radio standards used across Europe. EN 302 208 is its harmonised standard for UHF RFID interrogators, meaning the fixed readers and handhelds that run RAIN RFID systems. Testing against it is how a reader shows it meets the essential spectrum requirements of the Radio Equipment Directive, the EU law that governs radio equipment placed on the European market. Once a harmonised standard is cited in the EU’s Official Journal, compliance with it gives a manufacturer presumption of conformity, which in practice is the route to the CE mark.

The draft was produced by ETSI’s radio spectrum committee TC ERM, working group WG34. If it passes the vote it becomes V3.5.1 and replaces V3.4.1, which has been the reference version since December 2023.

What is not changing. The lower band stays at 865 to 868 MHz with up to 2 W ERP, on the same four 200 kHz reader channels centred on 865.7, 866.3, 866.9 and 867.5 MHz. The upper band stays at 915 to 921 MHz with up to 4 W ERP, on 400 kHz channels centred on 916.3, 917.5, 918.7 and 919.9 MHz. ERP is effective radiated power, the power a transmitter appears to radiate relative to a half-wave dipole, and it is the measure European spectrum rules are written in. The three reader categories are unchanged too: category I above 30 dBm ERP, category II from 13 to 30 dBm, and category III at 13 dBm or below.

What is changing. Annex B, which covers radiated measurements, has been reworked so that it no longer depends on IEEE/ANSI C63.5, a United States test standard for antenna calibration. The rewrite followed comments from the European Commission, and removing that external dependency is what the Commission wants to see before it will cite the standard in the Official Journal. For a manufacturer this is a laboratory question rather than a product one: the limits a reader has to meet are the same, but the way a test house demonstrates compliance against them is not.

The legal references have also been brought up to date. The lower band now cites Decision (EU) 2025/105. The upper band now cites Commission Implementing Decision (EU) 2025/650 of 26 March 2025, which amended Implementing Decision (EU) 2018/1538, the decision that harmonised 915 to 921 MHz for short range devices in the first place and opened the upper band to RFID.

That is where the interesting detail appears. The draft says that channels 3, 6 and 9 of the upper band rest on the 2025 EU decision. Channel 12, the 400 kHz slot from 919.7 to 920.1 MHz centred on 919.9 MHz, is described as having been based on ERC Recommendation 70-03 instead, and the draft points readers to the list of countries that have implemented it. ERC Recommendation 70-03 is the short range device recommendation maintained by CEPT, the European Conference of Postal and Telecommunications Administrations. Unlike an EU implementing decision it is not binding, and each national regulator decides for itself whether and how to adopt any given entry.

The reason for the difference is not hard to see on a frequency plan. Channel 12 sits inside 919.4 to 925 MHz, which the EU harmonised in 2021, under Commission Implementing Decision (EU) 2021/1730, for Railway Mobile Radio. That allocation is paired with 874.4 to 880 MHz and is intended for FRMCS, the Future Railway Mobile Communication System, the 5G-based successor to GSM-R, the 2G-derived radio system European railways have run since the early 2000s. The RFID draft itself defines the railways’ extended GSM band of 918 to 921 MHz and lists FRMCS among its abbreviations, which tells you the drafters had the neighbouring service firmly in mind.

Reading those citations together, the practical position in the EU looks like three upper-band channels that any member state implementing the 2025 decision should offer, and a fourth that is left to national decision in spectrum where railway radio has the stronger claim. That is an interpretation of the citations rather than a statement the draft makes, and it should be read as such.

The draft also sets out a control requirement for the upper band. Readers “shall have means that limit the channels to be used”, and that is tested under clause 5.5.9 with a 10-minute spectrum capture across 860 to 930 MHz. The draft adds that upper-band readers should be able to block operation in countries where parts of the band are reserved for military or government use. One caveat matters here: it could not be confirmed whether this requirement is new in V3.5.0 or carried over from V3.4.1, because the change log does not mention it and the two versions were not compared side by side. It is in the draft, but it should not be described as a new obligation without that check.

It is tempting to conclude that FRMCS coexistence drove this revision, but that is a reasonable question rather than an established fact. The only change ETSI logs is the test methodology, and the railway material may simply be housekeeping that aligns the document with allocations made in 2021 and 2025. Treat the coexistence theory as unconfirmed.

If the vote passes, the usual harmonised standard timetable follows. National standards bodies get three months to announce the new version, a further six months to adopt it, and eighteen months after that to withdraw any conflicting national standard. Separately, the Commission has to cite the standard in the Official Journal before it confers presumption of conformity under the Radio Equipment Directive, and the Annex B rework is the condition the Commission attached to doing so.

For anyone who specifies, sells or installs readers in Europe, three things follow. Reader and handheld makers should expect recertification work against the revised radiated test methods, and should be talking to their test houses now rather than in 2027. Integrators planning high-density upper-band installations at airports, parcel hubs and retail distribution centres can design around three 4 W channels across the EU, but should treat channel 12 as a country-by-country question and check national implementation of ERC Recommendation 70-03 before counting it in a dense reader mode plan. And anyone writing a tender should note that the upper band remains a national option, not an EU-wide guarantee, with patchy uptake since V3.3.1 added it in 2020.

We track the EU upper band and its amendments in the RFID mandates tracker entry for 915 to 921 MHz, and more on reader hardware and certification is gathered in our RFID readers coverage.

Read more at https://www.etsi.org/deliver/etsi_en/302200_302299/302208/03.05.00_20/en_302208v030500ev.pdf

Newsletter

Get the week in RFID, every Thursday

One email: implementations, hardware and tag launches, case studies and analysis. Free, and you can leave whenever you like.

We send one digest a week and nothing else. Unsubscribe in one click. See our privacy policy.

By Matt Houldsworth

Over 3 decades of experience in RFID, High Risk/Value Asset Management, Inspection Systems, Brand Protection Technology, Customer engagement technology, WIP management, Logistics tracking, Digital Product Passports (DPP), and Digital Twinning linked to physical products with RFID. My Veribli Tech Makes Circular Economies Work!