Checkpoint Systems and Impinj say they have found a way round one of the oldest problems in RAIN RFID: reading tags on bottles full of liquid. Checkpoint’s SmartShrink puts the RFID inlay inside the shrink band that seals a bottle cap, so the tag sits on the plastic closure above the liquid rather than on a label against it. The chip is from Impinj’s M800 series and supports Gen2X, Impinj’s extensions to the standard RAIN protocol. In Checkpoint’s own tests, a Gen2X handheld counted a batch of about 50 one-gallon containers in 5.1 seconds, against 10.6 seconds using standard Gen2. The companies published the results on 19 November.
The timing matters. Retailers, Walmart above all, are moving RAIN RFID out of apparel and into categories full of liquids: health and beauty, household products and, eventually, food. A tagging method that works on a T-shirt does not automatically work on a bottle of mouthwash, and suppliers in those categories have been waiting for answers they can put on a filling line.
Why liquids are hard to read
A passive RAIN tag has no battery. It powers itself from the reader’s radio signal and answers by reflecting part of that signal back, a process called backscatter, which we explain in The Physics of RFID. Water gets in the way twice. It absorbs energy in the 860 to 960 MHz band that RAIN uses, so less power reaches the chip, and it detunes the tag’s antenna when the antenna sits against it, so the tag captures less of what does arrive. The companies add two more problems common in shops: curved containers that stop a flat label lying properly, and metal shelving that reflects and distorts the signal.
The usual result is a tag that reads well on an empty sample in the lab and poorly on a full shelf in a store. Our guides to what affects read range and choosing a tag for your environment cover the wider picture.
What SmartShrink does differently
SmartShrink is built for liquid-filled containers. The inlay is built into a shrink band that is applied during filling and capping, when the band is shrunk tightly round the cap. Because the tag travels on the band rather than on the main label, Checkpoint says a manufacturer can add RFID without redesigning its label.

Louis Parker, RFID market development manager at Checkpoint, set out the reasoning at the AIM RFID Community Connect conference in May. His slides, given with AsReader and published by AIM, describe two problems with bottle tagging and one fix for both. Liquids and metal stop tags reading, so the tag goes above the fill line and on the plastic cap, where there is no metal or foil. Adhesive labels lift and fall off, because of container shape, poor adhesive, applicator problems or the conditions the product lives in, and a tag that has fallen off is no tag at all. Building the inlay into the shrink band means there is no adhesive to fail. The slides list other claims for the band: it fits odd-shaped, ribbed and child-resistant caps, it is tamper-evident, it can be pre-encoded or encoded on the line, it has perforations so the consumer can remove it for recycling, and the inlay is approved by ARC, the Auburn University lab whose approvals retailers use for mandate compliance.
Checkpoint lists health and beauty, food and beverage, pharmaceuticals, home care and home improvement, garden and automotive products as target categories. Checkpoint is part of CCL Industries, whose third-quarter results last week reported good volume growth in RFID at the division.
What Gen2X adds
Placement does the first half of the job. The chip does the second. The M800 is Impinj’s current high-performance tag chip, and Impinj lists read sensitivity of minus 25.5 dBm with a dipole antenna on its product page. Gen2X is a set of extensions to the Gen2 air protocol that every RAIN reader speaks. Impinj says it improves read performance on small tags, liquids, metals and densely packed products, which is a fair description of a shelf of shampoo.
The catch, as with every Gen2X story we have covered, is that the reader has to support Gen2X as well as the tag. A Gen2X tag still answers an ordinary Gen2 reader, so nothing breaks, but the gains in these tests only appear on Gen2X hardware. That base is growing: Zebra added Gen2X across its RFID range in September, and new readers such as Myruns’ R1 Series ship with it.
The test results
Checkpoint tested around 50 one-gallon liquid containers fitted with M800 SmartShrink inlays, using a handheld reader built on an Impinj E Family reader chip with Gen2X support. Two tests are reported.
- Handheld, close range: the time to read every container fell from 10.6 seconds with Gen2 to 5.1 seconds with Gen2X, a 52% cut.
- Stationary, one metre, five seconds: the reader read 89% of the tagged containers with Gen2X, against 74% with Gen2.

The chart describes the second result as a 15% increase in items read. It is 15 percentage points. On these figures that is about a fifth more containers read in the same five seconds (89 divided by 74 is 1.2), so the headline undersells it slightly rather than oversells it.
Halving a handheld count sounds like a saving of five seconds, and on 50 containers it is. The point Checkpoint makes is what that means across a store. A stock check is a member of staff walking aisles with a handheld, and every shelf of hard-to-read stock is a place where they slow down and hold the reader still, waiting for the last items to answer. Faster reads on liquids shorten the slowest part of the walk.
What the tests do not tell us
These are the companies’ own tests, published by the companies, and the scope is narrow. Buyers should read them as a promising start, not a specification.
- One container type. The test used one-gallon containers, large jugs with a big cap. The product photographs show SmartShrink on items as small as a lip gloss tube, where the band, and so the antenna, is far smaller. No results are given for small items.
- One distance. The release says Gen2X improved accuracy across multiple read distances, but only the one metre figure is published.
- About 50 items. A full shelf of shampoo or a pallet of household cleaner is far denser, with containers pressed against each other, which is a harder test.
- 89% is not 100%. The stationary figure is what was read in five seconds, not the share that could never be read. A reader left longer may get the rest, but the release does not say.
- No shelf conditions. Metal shelving is named as one of the problems, but the release does not say whether the containers were tested on it.
- The reader is not named. “E Family handheld” describes the reader chip inside, which several handheld makers use, not a particular product.
None of that undermines the result, which is a like-for-like comparison of Gen2 and Gen2X on the same tags. It does mean a supplier should do what Checkpoint’s own presentation recommends: send product samples for testing on its own packaging before committing a line.
The mandate question
Parker made the commercial pitch plainly. “Combining our innovative SmartShrink inlay design with the performance of Gen2X-enabled Impinj M800 series endpoints is enabling retailers to reliably and efficiently inventory traditionally difficult-to-tag liquid containers,” he said. “SmartShrink makes retail mandate compliance and inventory visibility simple, scalable, and disruption-free, especially for the products that need it most.”
The companies name Walmart as one of the retailers expanding RAIN RFID into more categories. As our guide to the Walmart RFID mandate sets out, grocery, consumables and pharmacy were not mandated as of August 2026, but health and beauty, consumables and, in time, grocery are widely expected to be next. That is exactly the territory SmartShrink is aimed at. A supplier facing a tagging deadline on bottled products has three broad choices: a label tag designed for liquids, a tag built into the packaging itself, or a tag on the closure. SmartShrink is the third, and its selling point is that it changes the cap seal rather than the label artwork.
Supply, and the bigger picture
There is one practical point for anyone planning a large rollout. At its third-quarter results, Impinj said M800 demand had run ahead of supply, with backlog up and some bookings already running into the first quarter of 2027. Suppliers planning SmartShrink at volume should discuss delivery timing with Checkpoint early.
Impinj frames the work as part of what it calls Physical Intelligence: getting accurate data about physical items into enterprise systems, which it argues matters more as retailers automate and lean on AI. Set the branding aside and the argument is a simple one. An RFID programme that covers clothing but not the shampoo aisle leaves a gap in the stock data, and the companies say closing it supports more accurate inventory, better shelf availability, faster replenishment and fewer blind spots. Liquids have been one of the largest gaps. If tags on the cap, read with Gen2X, hold up beyond one-gallon jugs, that gap gets a lot smaller.
More detail is in the Checkpoint Systems listing and the Impinj listing in the RFID News directory.

