RFID News

News and knowledge for the RFID industry

Vanch launches VF-L308 and VF-A308 eight-port RAIN readers on Impinj E710, with a choice of Linux or Android

Shenzhen Vanch Intelligent Technology has added two fixed RAIN UHF readers to its industrial range, the VF-L308 and the VF-A308. The two are the same piece of hardware with a different operating system loaded: the VF-L308 ships with Linux 4.19, the VF-A308 with Android 13. Both carry eight antenna ports and are built around Impinj’s E710 reader chip. The launch reached the trade on 18 November 2026 through the RAIN Alliance’s member news channel.

That channel is worth noting first. Member news on the Alliance’s site is material supplied by the member company and published as received, not RAIN Alliance reporting and not an endorsement. The Alliance is the industry body for passive UHF RFID, the technology defined by the EPC Gen2 air interface and catalogued as ISO 18000-6C. Vanch’s own product pages carry the same specifications, and that is where the figures below have been checked.

Vanch is a Shenzhen manufacturer founded in 2006 that builds industrial RFID readers, antennas, tags and printers. It describes itself as a National High-Tech Enterprise, says its products sell into more than 70 countries and regions, and claims more than 2,000 project customers.

Vanch's product showroom in Shenzhen, with display counters of RFID hardware, VANCH branding and an 18th anniversary poster.
Vanch’s own showroom in Shenzhen. The company has been building industrial RFID hardware since 2006.

On the radio side both models use the Impinj E710, a reader system-on-chip Impinj introduced in June 2021 to replace its long-running Indy line. Output power is continuously adjustable from 0 to 33 dBm into a 50 ohm load, receive sensitivity is quoted as better than or equal to -87 dBm, and peak inventory speed as more than 950 tags per second. With a 9 dBi antenna Vanch quotes a typical read range of 0 to 25 m, depending on the tag. There are eight 50 ohm TNC antenna ports, the frequency range is 860 MHz to 960 MHz set by region, and frequency hopping or a fixed channel can be selected in software. RSSI reporting, tag filtering, antenna connection protection and device temperature monitoring are standard, with approvals for FCC Part 15 and ETSI territories, China, India, Japan, South Korea, Malaysia and Taiwan.

Angled three-quarter view of the Vanch VF-L308 fixed RFID reader, with eight TNC antenna ports along the top edge and four further connectors down the side.
Eight TNC antenna ports run along one edge of the casting, with the wired interfaces on the side.

The more interesting half of the specification is the compute. Both readers run a Rockchip RK3568, a quad-core Arm Cortex-A55 applications processor at 2.0 GHz with a Mali-G52 GPU and an on-die neural processing unit rated at 1 TOPS. An NPU is a fixed-function accelerator for the integer arithmetic small neural networks are built from, and 1 TOPS is a modest but usable amount of it. There is 2 GB of RAM and 16 GB of storage, which Vanch says can be specified larger.

What that buys an integrator is work they no longer send upstream. A read point inventorying at several hundred tags a second produces a lot of duplicate traffic, which conventionally all goes to a middleware server to be deduplicated, windowed and thresholded. Filtering on the reader cuts the volume on the wire, keeps decision latency local when a read has to fire a GPIO output, and makes simple inference possible at the read point: judging whether a pallet is moving through a doorway or parked beside it.

Interfaces are generous. As standard there is Gigabit RJ45 with PoE for power and data, RS232 and RS485 serial at 9600 to 115200 bps, four optically isolated inputs and four optically isolated outputs, an HDMI 2.0 output good for 4K at 60 frames per second, two USB 3.0 ports, a TF card slot and a Nano-SIM slot. Wiegand, Wi-Fi, Bluetooth, GPS and 4G or 5G are options. The readers speak MQTT and HTTPS, take remote configuration over the web, accept firmware by local USB or over the network, and come with .NET, C++ and Java SDKs.

Close view of the input and output edge of the Vanch VF-L308 reader, showing a green pluggable terminal block for the GPIO, a DB9 serial port, USB 3.0, a USB OTG port, RJ45 and the power connector.
The wired edge: a pluggable terminal block for the eight isolated GPIO lines, DB9 serial, USB 3.0, USB OTG, RJ45 and power.

Physically it is a die-cast aluminium box of 214 x 148 x 30 mm, with a six-layer immersion-gold PCB inside. Protection is IP53, operating temperature -20 C to +70 C, and power draw 10 W at the full 33 dBm output. IP53 covers dust and falling water only, so this is a reader for inside a building rather than an unprotected yard gantry.

Six-view orthographic drawing of the Vanch VF-L308 fixed RFID reader showing the top, front, rear, both sides and the input and output edge.
Vanch’s dimensioned drawing of the unit, which measures 214 x 148 x 30 mm.

The applications Vanch names are the usual industrial set: automated high-bay warehousing and WMS stock management, in-plant logistics movements, fixed asset management, personnel access control and vehicle identification, and process work in 3C electronics, photovoltaic and lithium battery production, semiconductor manufacturing and automotive MES production lines.

Taken as a whole this is a routine product launch rather than a step change. The E710 has been available to reader builders since 2021, and eight-port fixed readers offered with a choice of Linux or Android are a crowded category: Impinj’s own partner listings include rival readers sold with either operating system, and Vanch already sells Android and Linux integrated readers of its own. The genuinely new elements are the RK3568 and its NPU, which make on-reader edge processing practical rather than theoretical, and putting both operating systems on identical hardware. That removes a procurement decision: one chassis and one spare part, with the software stack left to the application team.

What is absent is everything commercial. No price, no availability date, no named customers or deployments, and no announcement on Vanch’s own site to anchor a launch to. Until some of that appears there is nothing to weigh up beyond the specification sheet. Terms used here are defined in the RFID News glossary, and more on this class of kit sits in our RFID readers and RAIN RFID coverage.

Read more at the VF-L308 product page and the VF-A308 product page.

Newsletter

Get the week in RFID, every Thursday

One email: implementations, hardware and tag launches, case studies and analysis. Free, and you can leave whenever you like.

We send one digest a week and nothing else. Unsubscribe in one click. See our privacy policy.

By Matt Houldsworth

Over 3 decades of experience in RFID, High Risk/Value Asset Management, Inspection Systems, Brand Protection Technology, Customer engagement technology, WIP management, Logistics tracking, Digital Product Passports (DPP), and Digital Twinning linked to physical products with RFID. My Veribli Tech Makes Circular Economies Work!